Ležajevi glavčine bicikla: vjenčić s kuglicama, slobodne kuglice i industrijski ležaj

Technical tips · Tools

Hub bearing calculator:
Shimano and DT Swiss

Pick the brand, hub model and bearing position, then get the bearing code and dimensions, with a source and a reliability rating for every entry.

By Marko Ristivojević, Master Bike Mechanic

In short

Which bearing fits my hub? A hub bearing is defined by three measurements: inner diameter, outer diameter and width. A code such as 6902 or 6802 is shorthand for them. The calculator gives the code for Shimano and DT Swiss hubs, with a source. If an entry is unconfirmed, measure the bearing before you buy.

Brands

Shimano and DT Swiss, plus a few e*thirteen, Sunringlé and Fulcrum models

Data

Every entry has a source link, and the list keeps growing

Reliability

Green is manufacturer data, orange is a retailer quoting the manufacturer code, red means measure it

Before you buy

Measure the old bearing with calipers: inner diameter, outer diameter and width

Author: Marko Ristivojević, Master Bike Mechanic · BK MTB Evolution, Istočno Sarajevo

Hub bearing calculator

Choose the brand, the hub model and the bearing position. You get the bearing code and dimensions, with a source and a reliability rating.

The result will appear here.

Reliability: Manufacturer is data from the manufacturer's service documentation. Retailer with code is a retailer quoting the manufacturer code. Unconfirmed means the bearing should be measured. The marking on a seal (for example 6902) is not always accurate, so check the inner diameter, outer diameter and width with calipers before you buy.

How the calculator works

The calculator covers Shimano and DT Swiss hubs, plus a few e*thirteen, Sunringlé and Fulcrum models. Every row in the database has a source, and the data keeps being extended.

Replace a bearing only after you have measured the old one. For how a hub is taken apart and serviced, see the hub bearings guide.

How to choose a bearing: the hub bearing calculator step by step

Brand and model. Choose the brand and the exact hub model. On DT Swiss, the DT ID number is printed on the rim.

Bearing position. Front and rear hubs use different bearings, and within one hub the left and right side or the freehub can differ in size.

Reliability. Green is data from the manufacturer's documentation, orange is a retailer quoting the manufacturer code, and red means the bearing should be measured.

What a bearing code means: 6902, 6802 and 6803

6902. A 15 × 28 × 7 mm bearing. It is common in DT Swiss hubs, and it is also the size of one of the two bearings in the Shimano XT M8210 rear hub.

6802. A 15 × 24 × 5 mm bearing, thinner and smaller than 6902.

6803. A 17 × 26 × 5 mm bearing. Some retailers wrongly list it as 6903.

How to read the code. The last two digits give the bore diameter: 00 is 10 mm, 01 is 12 mm, 02 is 15 mm and 03 is 17 mm. The code 61902 is the same size as 6902.

Shimano hubs: loose balls or cartridge bearings

Cup and cone. Shimano XT M8110, SLX M7110 and Deore M6010 use balls in a retainer that are adjusted with a cone, not cartridge bearings.

Ball size. The M6010, M8010 and M7110 front hubs use 5/32" balls: 15 on the left and 17 on the right. The XT FH-M8110 rear hub has 3/16" × 13 on the right and 5/32" × 15 on the left.

Older hubs. Older front hubs (for example M6000, M7000 and M590) use 3/16" balls.

Cartridge bearings. The new XT M8210 uses cartridge bearings: 17 × 30 × 7 mm in the front hub, and 17 × 30 × 7 mm plus 15 × 28 × 7 mm in the rear hub.

DT Swiss hubs: which bearing fits which model

180 and 240 EXP. The DT manual lists 1526 (15 × 26 × 7 mm) on the drive side of the 180 and 6802 on the non-drive side, and 1526 on both sides of the 240 EXP.

Older 240s, 340 and 370. Mostly 6902 (15 × 28 × 7 mm), with 6802 (15 × 24 × 5 mm) on the non-drive side or in the freehub.

DT 350. Retailers list 6902 for the front and rear hub, but DT does not publish the freehub bearing size. Check the exact size for your hub in DT Swiss Product Support or measure the bearing.

Before you buy: how to measure a hub bearing

Remove the bearing. The marking on the seal is not always accurate, so do not rely on it alone.

Measure three dimensions. Use calipers to measure the inner diameter, outer diameter and width.

Check the clearance. Enduro advises confirming the bearing clearance (C3 or CN) specified by the hub manufacturer before you buy.

Pro tip: before you remove a bearing, write down or photograph which one sits on which side, because some hubs use two different bearings.

FAQ: Frequently asked questions about hub bearings

Which bearing fits a DT Swiss 350?

Retailers list 6902 (15 × 28 × 7 mm) for the front and rear 350 hub. DT does not publish the freehub bearing size and forums mention 6802, so measure it.

Which balls does the Shimano XT M8110 use?

The HB-M8110 front hub uses 5/32" balls: 15 on the left and 17 on the right. The FH-M8110 rear hub has 3/16" × 13 on the right and 5/32" × 15 on the left.

Is 61902 the same as 6902?

Yes, 61902 is the same size as 6902: 15 × 28 × 7 mm.

Can I buy a bearing from the seal marking alone?

I do not recommend it. Seal markings are not always accurate, so measure the inner diameter, outer diameter and width with calipers.